Aluminum die-casting foundries · Arkansas
ADC Manufacturing
Harrison, AR · ~57 workers · 2 years of OSHA Injury Tracking Application data.
- F
- Failing Safety Record
- 7.9
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
ADC Manufacturing runs at 239% of its industry's injury rate - far more dangerous than the typical Aluminum die-casting foundries workplace, earning a grade F.
- F
- Failing Safety Record
- 7.9
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 8
- recordable injuries tracked
Grade compares ADC Manufacturing's OSHA Total Case Rate to the BLS industry benchmark across 2 years of Form 300A filings (2016–2024). This reflects reported recordable injuries, not an independent safety inspection -- underreporting is a known limitation of employer self-recordkeeping.
Injury rate over time
ADC Manufacturing's yearly Total Case Rate, against the 3.3 industry benchmark.
Where ADC Manufacturing falls in its industry
223 Aluminum die-casting foundries establishmentsSafer than 21% of graded establishments in this industry, whose median TCR is 4.7.
Narrower to Arkansas alone (the establishments it most directly competes with for workers and contracts): ranked #13 safest of 14 Aluminum die-casting foundries employers in Arkansas.
ADC Manufacturing has an average TCR of 7.9, which is 239% of the industry average (3.3) for Aluminum die-casting foundries. This is significantly worse than average.
The letter grade is a transparent derived index PlainSafetyScore computes from public OSHA ITA and BLS benchmark data, not an official OSHA rating or safety certification. Full formula and thresholds: Methodology.
Trend analysis for ADC Manufacturing
Between 2020 and 2021, ADC Manufacturing's Total Case Rate improved from 10.9 to 4.8 recordable injuries per 100 full-time workers, a 56% decrease across 1 year of OSHA reporting.
The safest year on record was 2021, at a TCR of 4.8, while 2020 saw the highest rate, at 10.9, a spread of 6.1 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 2 reporting years, ADC Manufacturing recorded 8 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 2-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from ADC Manufacturing's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331523 - Aluminum die-casting foundries.
DART Rate, Transparent Calculation (2021)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
3 DART incidents × 200,000 ÷ 124,025 hours worked = 4.84 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| ADC Manufacturing (this establishment) | 7.88 | OSHA ITA Form 300A, 2-year avg |
| Aluminum die-castings, unfinished, manufacturing industry avg | 3.30 | BLS IIF, NAICS 331523 |
| Arkansas state avg (all industries) | 3.83 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by ADC Manufacturing to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2021: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2020: 7 reportable incidents · 5 injuries, 2 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2021 | 4.8 | 4.8 | 3 | 0 | 0 |
| 2020 | 10.9 | 6.2 | 5 | 2 | 0 |
What this grade means for you
Use this grade as a relative read on ADC Manufacturing's reported OSHA injury record versus its Aluminum die-casting foundries peers, not a verdict on whether any single site is safe today.
- At 239% of the Aluminum die-casting foundries benchmark, ADC Manufacturing reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Aluminum die-casting foundries sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is ADC Manufacturing's safety grade?
How many injuries has ADC Manufacturing reported?
Similar Employers
Matched by safety record across the industry and by workforce size within Arkansas - a different peer set than the category browse links below.
Similar TCR (~7.9)
Explore More Safety Data
Read our methodology - how this data is sourced, computed, and verified.
Related
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.