Pipe hangers and supports, metal, manufacturing · Rhode Island
Anvil EPS
North Kingstown, RI · ~125 workers · 4 years of OSHA Injury Tracking Application data.
- B
- Good Safety Record
- 2.6
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Anvil EPS runs at 80% of its industry's injury rate - safer than the typical Pipe hangers and supports, metal, manufacturing workplace, earning a grade B.
- B
- Good Safety Record
- 2.6
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 10
- recordable injuries tracked
Grade compares Anvil EPS's OSHA Total Case Rate of 2.6 to the Pipe hangers and supports, metal, manufacturing BLS benchmark of 3.3 (80% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Anvil EPS's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Anvil EPS falls in its industry
880 Pipe hangers and supports, met establishmentsSafer than 68% of graded establishments in this industry, whose median TCR is 4.2.
Narrower to Rhode Island alone (the establishments it most directly competes with for workers and contracts): ranked #3 safest of 6 Pipe hangers and supports, met employers in Rhode Island.
Trend analysis for Anvil EPS
Between 2016 and 2020, Anvil EPS's Total Case Rate worsened from 1.4 to 2.8 recordable injuries per 100 full-time workers, a 99% increase across 4 years of OSHA reporting.
The safest year on record was 2016, at a TCR of 1.4, while 2017 saw the highest rate, at 4.1, a spread of 2.7 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, Anvil EPS recorded 10 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 10 injuries, 3 illnesses shown on this page for Anvil EPS are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 332999 - Pipe hangers and supports, metal, manufacturing.
DART Rate, Transparent Calculation (2020)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 216,331 hours worked = 1.85 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Anvil EPS (this establishment) | 2.63 | OSHA ITA Form 300A, 4-year avg |
| Machine bases, metal, manufacturing industry avg | 3.30 | BLS IIF, NAICS 332999 |
| Rhode Island state avg (all industries) | 5.62 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Anvil EPS to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2020: 3 reportable incidents · 2 injuries, 1 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 5 reportable incidents · 3 injuries, 2 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2020 | 2.8 | 1.9 | 2 | 1 | 0 |
| 2018 | 2.3 | 0.8 | 3 | 0 | 0 |
| 2017 | 4.1 | 0.8 | 3 | 2 | 0 |
| 2016 | 1.4 | 1.4 | 2 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Anvil EPS's reported OSHA injury record, strong versus its Pipe hangers and supports, metal, manufacturing peers, but not a guarantee about any single site today.
- At 80% of the Pipe hangers and supports, metal, manufacturing benchmark, Anvil EPS reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Pipe hangers and supports, metal, manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Anvil EPS's safety grade?
How many injuries has Anvil EPS reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Rhode Island, and by nearby establishments in North Kingstown - a different peer set than the category browse links below.
Similar TCR (~2.6)
Similar size (~125 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.