Atek Metal Technologies
Open-data reference.
NEW HAMPTON, IA | Permanent mold castings, aluminum, unfinished, manufacturing
~177 avg employees | 7 years of OSHA data
Atek Metal Technologies has an average TCR of 7.0, which is 212% of the industry average (3.3) for Permanent mold castings, aluminum, unfinished, manufacturing. This is significantly worse than average.
Safety Insights for Atek Metal Technologies
Atek Metal Technologies operates an establishment with approximately 177 full-time equivalent workers in NEW HAMPTON, IA, classified under the Permanent mold castings, aluminum, unfinished, manufacturing industry (NAICS 331524). Across 7 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 81 recordable injuries, 3 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 7.0 injuries per 100 full-time workers per year provides the anchor metric for the F letter grade (Failing Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Permanent mold castings, aluminum, unfinished, manufacturing, Atek Metal Technologies's workforce experiences 212% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR above the benchmark flags a higher-than-typical risk profile for jobseekers, insurers, and enforcement agencies to examine.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 7 reporting cycles points to systemic hazard exposure. Readers evaluating Atek Metal Technologies as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Atek Metal Technologies's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 331524 — Permanent mold castings, aluminum, unfinished, manufacturing.
DART Rate — Transparent Calculation (2024)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
6 DART incidents × 200,000 ÷ 301,331 hours worked = 3.98 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Atek Metal Technologies (this establishment) | 6.99 | OSHA ITA Form 300A, 7-year avg |
| Sand castings, aluminum, unfinished, manufacturing industry avg | 3.30 | BLS IIF, NAICS 331524 |
| Iowa state avg (all industries) | 9.40 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Atek Metal Technologies to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 9 reportable incidents · 8 injuries, 1 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2023: 15 reportable incidents · 15 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2022: 27 reportable incidents · 26 injuries, 1 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2019: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2018: 9 reportable incidents · 9 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2017: 11 reportable incidents · 11 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2016: 10 reportable incidents · 9 injuries, 1 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 6.0 | 4.0 | 8 | 1 | 0 |
| 2023 | 7.1 | 3.3 | 15 | 0 | 0 |
| 2022 | 11.3 | 8.8 | 26 | 1 | 0 |
| 2019 | 2.2 | 1.5 | 3 | 0 | 0 |
| 2018 | 6.6 | 5.1 | 9 | 0 | 0 |
| 2017 | 8.6 | 3.9 | 11 | 0 | 0 |
| 2016 | 7.2 | 2.9 | 9 | 1 | 0 |
Frequently Asked Questions
What is Atek Metal Technologies's safety grade?
How is the safety grade calculated?
How many injuries has Atek Metal Technologies reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.