Copper Rolling, Drawing, Extruding, and Alloying · Texas
CCI-El Paso Facility
El Paso, TX · ~124 workers · 3 years of OSHA Injury Tracking Application data.
- A
- Excellent Safety Record
- 1.4
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
CCI-El Paso Facility runs at 44% of its industry's injury rate - far safer than the typical Copper Rolling, Drawing, Extruding, and Alloying workplace, earning a grade A.
- A
- Excellent Safety Record
- 1.4
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 7
- recordable injuries tracked
Grade compares CCI-El Paso Facility's OSHA Total Case Rate of 1.4 to the Copper Rolling, Drawing, Extruding, and Alloying BLS benchmark of 3.3 (44% of benchmark) across 3 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
CCI-El Paso Facility's yearly Total Case Rate, against the 3.3 industry benchmark.
Where CCI-El Paso Facility falls in its industry
206 Copper Rolling, Drawing, Extru establishmentsSafer than 78% of graded establishments in this industry, whose median TCR is 3.7.
Narrower to Texas alone (the establishments it most directly competes with for workers and contracts): ranked #8 safest of 19 Copper Rolling, Drawing, Extru employers in Texas.
Trend analysis for CCI-El Paso Facility
Between 2017 and 2019, CCI-El Paso Facility's Total Case Rate worsened from 0.6 to 1.9 recordable injuries per 100 full-time workers, a 206% increase across 2 years of OSHA reporting.
The safest year on record was 2017, at a TCR of 0.6, while 2019 saw the highest rate, at 1.9, a spread of 1.3 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 3 reporting years, CCI-El Paso Facility recorded 7 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 3-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 7 injuries shown on this page for CCI-El Paso Facility are sourced from its own 3 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331420 - Copper Rolling, Drawing, Extruding, and Alloying.
DART Rate, Transparent Calculation (2019)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 310,842 hours worked = 1.29 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| CCI-El Paso Facility (this establishment) | 1.45 | OSHA ITA Form 300A, 3-year avg |
| Aircraft and automotive wire or cable made from purchased copper in wire drawing plants industry avg | 3.30 | BLS IIF, NAICS 331420 |
| Texas state avg (all industries) | 3.73 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by CCI-El Paso Facility to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2019: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2019 | 1.9 | 1.3 | 3 | 0 | 0 |
| 2018 | 1.8 | 1.8 | 3 | 0 | 0 |
| 2017 | 0.6 | 0.6 | 1 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on CCI-El Paso Facility's reported OSHA injury record, strong versus its Copper Rolling, Drawing, Extruding, and Alloying peers, but not a guarantee about any single site today.
- At 44% of the Copper Rolling, Drawing, Extruding, and Alloying benchmark, CCI-El Paso Facility reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Copper Rolling, Drawing, Extruding, and Alloying sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is CCI-El Paso Facility's safety grade?
How many injuries has CCI-El Paso Facility reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Texas, and by nearby establishments in El Paso - a different peer set than the category browse links below.
Similar TCR (~1.4)
Similar size (~124 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.