Machine shops · Rhode Island
Guill Tool and Engineering, Co., Inc.
West Warwick, RI · ~67 workers · 2 years of OSHA Injury Tracking Application data.
- C
- Average Safety Record
- 2.8
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Guill Tool and Engineering, Co., Inc. runs at 86% of its industry's injury rate - about level with the typical Machine shops workplace, earning a grade C.
- C
- Average Safety Record
- 2.8
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 1
- recordable injuries tracked
Grade compares Guill Tool and Engineering, Co., Inc.'s OSHA Total Case Rate of 2.8 to the Machine shops BLS benchmark of 3.3 (86% of benchmark) across 2 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Guill Tool and Engineering, Co., Inc.'s yearly Total Case Rate, against the 3.3 industry benchmark.
Where Guill Tool and Engineering, Co., Inc. falls in its industry
2,037 Machine shops establishmentsSafer than 53% of graded establishments in this industry, whose median TCR is 3.1.
Narrower to Rhode Island alone (the establishments it most directly competes with for workers and contracts): ranked #4 safest of 9 Machine shops employers in Rhode Island.
Trend analysis for Guill Tool and Engineering, Co., Inc.
Between 2017 and 2018, Guill Tool and Engineering, Co., Inc.'s Total Case Rate worsened from 1.4 to 4.3 recordable injuries per 100 full-time workers, a 209% increase across 1 year of OSHA reporting.
The safest year on record was 2017, at a TCR of 1.4, while 2018 saw the highest rate, at 4.3, a spread of 2.9 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 2 reporting years, Guill Tool and Engineering, Co., Inc. recorded 1 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 2-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 1 injuries, 3 illnesses shown on this page for Guill Tool and Engineering, Co., Inc. are sourced from its own 2 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 332710 - Machine shops.
DART Rate, Transparent Calculation (2018)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
3 DART incidents × 200,000 ÷ 139,591 hours worked = 4.30 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Guill Tool and Engineering, Co., Inc. (this establishment) | 2.84 | OSHA ITA Form 300A, 2-year avg |
| Machine shops industry avg | 3.30 | BLS IIF, NAICS 332710 |
| Rhode Island state avg (all industries) | 5.62 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Guill Tool and Engineering, Co., Inc. to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2018: 3 reportable incidents · 0 injuries, 3 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2018 | 4.3 | 4.3 | 0 | 3 | 0 |
| 2017 | 1.4 | 0.0 | 1 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Guill Tool and Engineering, Co., Inc.'s reported OSHA injury record, strong versus its Machine shops peers, but not a guarantee about any single site today.
- At 86% of the Machine shops benchmark, Guill Tool and Engineering, Co., Inc. reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Machine shops sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Guill Tool and Engineering, Co., Inc.'s safety grade?
How many injuries has Guill Tool and Engineering, Co., Inc. reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Rhode Island, and by nearby establishments in West Warwick - a different peer set than the category browse links below.
Similar TCR (~2.8)
Similar size (~67 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.