Glazing contractors · Ohio
JMD Architectural Products, Inc
Tipp City, OH · ~23 workers · 4 years of OSHA Injury Tracking Application data.
- B
- Good Safety Record
- 1.4
- Avg TCR
- 2.8
- Industry avg
- 0
- Fatalities
The verdict
JMD Architectural Products, Inc runs at 52% of its industry's injury rate - safer than the typical Glazing contractors workplace, earning a grade B.
- B
- Good Safety Record
- 1.4
- avg TCR · per 100 workers
- 2.8
- industry benchmark (BLS)
- 2
- recordable injuries tracked
Grade compares JMD Architectural Products, Inc's OSHA Total Case Rate of 1.4 to the Glazing contractors BLS benchmark of 2.8 (52% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
JMD Architectural Products, Inc's yearly Total Case Rate, against the 2.8 industry benchmark.
Where JMD Architectural Products, Inc falls in its industry
602 Glazing contractors establishmentsSafer than 79% of graded establishments in this industry, whose median TCR is 3.6.
Narrower to Ohio alone (the establishments it most directly competes with for workers and contracts): ranked #4 safest of 29 Glazing contractors employers in Ohio.
Trend analysis for JMD Architectural Products, Inc
Between 2017 and 2023, JMD Architectural Products, Inc's Total Case Rate held roughly steady from 0.0 to 0.0 recordable injuries per 100 full-time workers, a 0% change across 6 years of OSHA reporting.
The safest year on record was 2017, at a TCR of 0.0, while 2019 saw the highest rate, at 5.8, a spread of 5.8 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, JMD Architectural Products, Inc recorded 2 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 2 injuries shown on this page for JMD Architectural Products, Inc are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 238150 - Glazing contractors.
DART Rate, Transparent Calculation (2023)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 49,036 hours worked = 0.00 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| JMD Architectural Products, Inc (this establishment) | 1.45 | OSHA ITA Form 300A, 4-year avg |
| Glass and Glazing Contractor industry avg | 2.80 | BLS IIF, NAICS 238150 |
| Ohio state avg (all industries) | 3.90 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by JMD Architectural Products, Inc to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2023: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2022: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2019: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2023 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2022 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2019 | 5.8 | 0.0 | 2 | 0 | 0 |
| 2017 | 0.0 | 0.0 | 0 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on JMD Architectural Products, Inc's reported OSHA injury record, strong versus its Glazing contractors peers, but not a guarantee about any single site today.
- At 52% of the Glazing contractors benchmark, JMD Architectural Products, Inc reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Glazing contractors sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is JMD Architectural Products, Inc's safety grade?
How many injuries has JMD Architectural Products, Inc reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Ohio, and by nearby establishments in Tipp City - a different peer set than the category browse links below.
Similar TCR (~1.4)
Similar size (~23 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.