Miller's Fab & Weld Corp.
Open-data reference.
RIVERSIDE, CA | Fabricated structural metal manufacturing
~19 avg employees | 4 years of OSHA data
Miller's Fab & Weld Corp. has an average TCR of 15.3, which is 463% of the industry average (3.3) for Fabricated structural metal manufacturing. This is significantly worse than average.
Safety Insights for Miller's Fab & Weld Corp.
Miller's Fab & Weld Corp. operates an establishment with approximately 19 full-time equivalent workers in RIVERSIDE, CA, classified under the Fabricated structural metal manufacturing industry (NAICS 332312). Across 4 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 8 recordable injuries, 0 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 15.3 injuries per 100 full-time workers per year provides the anchor metric for the F letter grade (Failing Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Fabricated structural metal manufacturing, Miller's Fab & Weld Corp.'s workforce experiences 463% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR above the benchmark flags a higher-than-typical risk profile for jobseekers, insurers, and enforcement agencies to examine.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 4 reporting cycles points to systemic hazard exposure. Readers evaluating Miller's Fab & Weld Corp. as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Miller's Fab & Weld Corp.'s own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 332312 — Fabricated structural metal manufacturing.
DART Rate — Transparent Calculation (2022)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 16,208 hours worked = 0.00 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Miller's Fab & Weld Corp. (this establishment) | 15.29 | OSHA ITA Form 300A, 4-year avg |
| Structural steel, fabricated, manufacturing industry avg | 3.30 | BLS IIF, NAICS 332312 |
| California state avg (all industries) | 58.88 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Miller's Fab & Weld Corp. to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2022: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2021: 4 reportable incidents · 4 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2020: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2017: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2022 | 12.3 | 0.0 | 1 | 0 | 0 |
| 2021 | 31.8 | 31.8 | 4 | 0 | 0 |
| 2020 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2017 | 17.0 | 5.7 | 3 | 0 | 0 |
Frequently Asked Questions
What is Miller's Fab & Weld Corp.'s safety grade?
How is the safety grade calculated?
How many injuries has Miller's Fab & Weld Corp. reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.