Cutters, metal milling, manufacturing · Ohio
National Blanking
Toledo, OH · ~21 workers · 4 years of OSHA Injury Tracking Application data.
- C
- Average Safety Record
- 2.8
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
National Blanking runs at 83% of its industry's injury rate - about level with the typical Cutters, metal milling, manufacturing workplace, earning a grade C.
- C
- Average Safety Record
- 2.8
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 3
- recordable injuries tracked
Grade compares National Blanking's OSHA Total Case Rate of 2.8 to the Cutters, metal milling, manufacturing BLS benchmark of 3.3 (83% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
National Blanking's yearly Total Case Rate, against the 3.3 industry benchmark.
Where National Blanking falls in its industry
276 Cutters, metal milling, manufa establishmentsSafer than 35% of graded establishments in this industry, whose median TCR is 1.9.
Narrower to Ohio alone (the establishments it most directly competes with for workers and contracts): ranked #31 safest of 38 Cutters, metal milling, manufa employers in Ohio.
Trend analysis for National Blanking
Between 2016 and 2024, National Blanking's Total Case Rate improved from 11.0 to 0.0 recordable injuries per 100 full-time workers, a 100% decrease across 8 years of OSHA reporting.
The safest year on record was 2022, at a TCR of 0.0, while 2016 saw the highest rate, at 11.0, a spread of 11.0 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, National Blanking recorded 3 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 3 injuries shown on this page for National Blanking are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 333515 - Cutters, metal milling, manufacturing.
DART Rate, Transparent Calculation (2024)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 32,315 hours worked = 0.00 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| National Blanking (this establishment) | 2.75 | OSHA ITA Form 300A, 4-year avg |
| Dies and taps (i.e., a machine tool accessory) manufacturing industry avg | 3.30 | BLS IIF, NAICS 333515 |
| Ohio state avg (all industries) | 3.90 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by National Blanking to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2023: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2022: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2023 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2022 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2016 | 11.0 | 11.0 | 3 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on National Blanking's reported OSHA injury record, strong versus its Cutters, metal milling, manufacturing peers, but not a guarantee about any single site today.
- At 83% of the Cutters, metal milling, manufacturing benchmark, National Blanking reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Cutters, metal milling, manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is National Blanking's safety grade?
How many injuries has National Blanking reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Ohio, and by nearby establishments in Toledo - a different peer set than the category browse links below.
Similar TCR (~2.8)
Similar size (~21 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.