Custom roll forming metal products · Minnesota
ACME Metal Spinning
Fridley, MN · ~22 workers · 3 years of OSHA Injury Tracking Application data.
- D
- Poor Safety Record
- 6.1
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
ACME Metal Spinning runs at 184% of its industry's injury rate - more dangerous than the typical Custom roll forming metal products workplace, earning a grade D.
- D
- Poor Safety Record
- 6.1
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 3
- recordable injuries tracked
Grade compares ACME Metal Spinning's OSHA Total Case Rate to the BLS industry benchmark across 3 years of Form 300A filings (2016–2024). This reflects reported recordable injuries, not an independent safety inspection -- underreporting is a known limitation of employer self-recordkeeping.
Injury rate over time
ACME Metal Spinning's yearly Total Case Rate, against the 3.3 industry benchmark.
Where ACME Metal Spinning falls in its industry
101 Custom roll forming metal prod establishmentsSafer than 39% of graded establishments in this industry, whose median TCR is 5.0.
ACME Metal Spinning has an average TCR of 6.1, which is 184% of the industry average (3.3) for Custom roll forming metal products. This is worse than average.
The letter grade is a transparent derived index PlainSafetyScore computes from public OSHA ITA and BLS benchmark data, not an official OSHA rating or safety certification. Full formula and thresholds: Methodology.
Trend analysis for ACME Metal Spinning
Between 2021 and 2024, ACME Metal Spinning's Total Case Rate held roughly steady from 0.0 to 9.1 recordable injuries per 100 full-time workers, a 0% change across 3 years of OSHA reporting.
The safest year on record was 2021, at a TCR of 0.0, while 2023 saw the highest rate, at 9.1, a spread of 9.1 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 3 reporting years, ACME Metal Spinning recorded 3 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 3-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from ACME Metal Spinning's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 332114 - Custom roll forming metal products.
DART Rate, Transparent Calculation (2024)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 44,000 hours worked = 0.00 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| ACME Metal Spinning (this establishment) | 6.06 | OSHA ITA Form 300A, 3-year avg |
| Custom roll forming metal products industry avg | 3.30 | BLS IIF, NAICS 332114 |
| Minnesota state avg (all industries) | 5.18 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by ACME Metal Spinning to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2023: 2 reportable incidents · 1 injuries, 1 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2021: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 9.1 | 0.0 | 2 | 0 | 0 |
| 2023 | 9.1 | 4.5 | 1 | 1 | 0 |
| 2021 | 0.0 | 0.0 | 0 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on ACME Metal Spinning's reported OSHA injury record versus its Custom roll forming metal products peers, not a verdict on whether any single site is safe today.
- At 184% of the Custom roll forming metal products benchmark, ACME Metal Spinning reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Custom roll forming metal products sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is ACME Metal Spinning's safety grade?
How many injuries has ACME Metal Spinning reported?
Similar Employers
Matched by safety record across the industry and by workforce size within Minnesota - a different peer set than the category browse links below.
Similar TCR (~6.1)
Explore More Safety Data
Read our methodology - how this data is sourced, computed, and verified.
Related
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.