Connector Manufacturing - Hamilton
Open-data reference.
HAMILTON, OH | Lugs and connectors, electrical, manufacturing
~156 avg employees | 4 years of OSHA data
Connector Manufacturing - Hamilton has an average TCR of 4.5, which is 137% of the industry average (3.3) for Lugs and connectors, electrical, manufacturing. This is worse than average.
Safety Insights for Connector Manufacturing - Hamilton
Connector Manufacturing - Hamilton operates an establishment with approximately 156 full-time equivalent workers in HAMILTON, OH, classified under the Lugs and connectors, electrical, manufacturing industry (NAICS 335931). Across 4 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 23 recordable injuries, 5 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 4.5 injuries per 100 full-time workers per year provides the anchor metric for the D letter grade (Poor Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Lugs and connectors, electrical, manufacturing, Connector Manufacturing - Hamilton's workforce experiences 137% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR above the benchmark flags a higher-than-typical risk profile for jobseekers, insurers, and enforcement agencies to examine.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 4 reporting cycles points to systemic hazard exposure. Readers evaluating Connector Manufacturing - Hamilton as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Connector Manufacturing - Hamilton's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 335931 — Lugs and connectors, electrical, manufacturing.
DART Rate — Transparent Calculation (2019)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
1 DART incidents × 200,000 ÷ 344,313 hours worked = 0.58 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Connector Manufacturing - Hamilton (this establishment) | 4.51 | OSHA ITA Form 300A, 4-year avg |
| Arrestors and coils, lighting, manufacturing industry avg | 3.30 | BLS IIF, NAICS 335931 |
| Ohio state avg (all industries) | 31.77 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Connector Manufacturing - Hamilton to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2019: 5 reportable incidents · 3 injuries, 2 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2018: 9 reportable incidents · 9 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2017: 7 reportable incidents · 4 injuries, 3 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2016: 7 reportable incidents · 7 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2019 | 2.9 | 0.6 | 3 | 2 | 0 |
| 2018 | 6.0 | 3.3 | 9 | 0 | 0 |
| 2017 | 4.6 | 2.6 | 4 | 3 | 0 |
| 2016 | 4.6 | 3.3 | 7 | 0 | 0 |
Frequently Asked Questions
What is Connector Manufacturing - Hamilton's safety grade?
How is the safety grade calculated?
How many injuries has Connector Manufacturing - Hamilton reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.