Motor vehicle moldings and extrusions, plastics, manufacturing · Alabama
Inzi Controls Alabama Inc
Elba, AL · ~142 workers · 3 years of OSHA Injury Tracking Application data.
- D
- Poor Safety Record
- 5.8
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Inzi Controls Alabama Inc runs at 177% of its industry's injury rate - more dangerous than the typical Motor vehicle moldings and extrusions, plastics, manufacturing workplace, earning a grade D.
- D
- Poor Safety Record
- 5.8
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 16
- recordable injuries tracked
Grade compares Inzi Controls Alabama Inc's OSHA Total Case Rate of 5.8 to the Motor vehicle moldings and extrusions, plastics, manufacturing BLS benchmark of 3.3 (177% of benchmark) across 3 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Inzi Controls Alabama Inc's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Inzi Controls Alabama Inc falls in its industry
2,995 Motor vehicle moldings and ext establishmentsSafer than 24% of graded establishments in this industry, whose median TCR is 3.4.
Narrower to Alabama alone (the establishments it most directly competes with for workers and contracts): ranked #52 safest of 68 Motor vehicle moldings and ext employers in Alabama.
Trend analysis for Inzi Controls Alabama Inc
Between 2017 and 2023, Inzi Controls Alabama Inc's Total Case Rate improved from 10.0 to 3.4 recordable injuries per 100 full-time workers, a 66% decrease across 6 years of OSHA reporting.
The safest year on record was 2023, at a TCR of 3.4, while 2017 saw the highest rate, at 10.0, a spread of 6.6 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 3 reporting years, Inzi Controls Alabama Inc recorded 16 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 3-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 16 injuries, 7 illnesses shown on this page for Inzi Controls Alabama Inc are sourced from its own 3 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 326199 - Motor vehicle moldings and extrusions, plastics, manufacturing.
DART Rate, Transparent Calculation (2023)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
1 DART incidents × 200,000 ÷ 179,271 hours worked = 1.12 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Inzi Controls Alabama Inc (this establishment) | 5.83 | OSHA ITA Form 300A, 3-year avg |
| Fiberglass Pool Manufacturing industry avg | 3.30 | BLS IIF, NAICS 326199 |
| Alabama state avg (all industries) | 4.09 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Inzi Controls Alabama Inc to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2023: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 6 reportable incidents · 5 injuries, 1 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 14 reportable incidents · 8 injuries, 6 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2023 | 3.4 | 1.1 | 3 | 0 | 0 |
| 2018 | 4.2 | 0.0 | 5 | 1 | 0 |
| 2017 | 10.0 | 0.0 | 8 | 6 | 0 |
What this grade means for you
Use this grade as a relative read on Inzi Controls Alabama Inc's reported OSHA injury record versus its Motor vehicle moldings and extrusions, plastics, manufacturing peers, not a verdict on whether any single site is safe today.
- At 177% of the Motor vehicle moldings and extrusions, plastics, manufacturing benchmark, Inzi Controls Alabama Inc reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Motor vehicle moldings and extrusions, plastics, manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Inzi Controls Alabama Inc's safety grade?
How many injuries has Inzi Controls Alabama Inc reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Alabama, and by nearby establishments in Elba - a different peer set than the category browse links below.
Similar TCR (~5.8)
Similar size (~142 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.