Tungsten carbide powder made by metallurgical process · West Virginia

JM Tungste-Met

Oak Hill, WV · ~59 workers · 4 years of OSHA Injury Tracking Application data.

C
Average Safety Record
3.7
Avg TCR
3.3
Industry avg
0
Fatalities

The verdict

JM Tungste-Met runs at 111% of its industry's injury rate - about level with the typical Tungsten carbide powder made by metallurgical process workplace, earning a grade C.

C
Average Safety Record
3.7
avg TCR · per 100 workers
3.3
industry benchmark (BLS)
5
recordable injuries tracked

Grade compares JM Tungste-Met's OSHA Total Case Rate of 3.7 to the Tungsten carbide powder made by metallurgical process BLS benchmark of 3.3 (111% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.

Injury rate over time

JM Tungste-Met's yearly Total Case Rate, against the 3.3 industry benchmark.

-5051015 2016201720182019 33.3 Industry benchmarkJM Tungste-Met TCR
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 331492.

Where JM Tungste-Met falls in its industry

139 Tungsten carbide powder made b establishments

Safer than 47% of graded establishments in this industry, whose median TCR is 3.6.

More dangerous than peersSafer than peers

Trend analysis for JM Tungste-Met

Between 2016 and 2019, JM Tungste-Met's Total Case Rate improved from 11.7 to 3.0 recordable injuries per 100 full-time workers, a 75% decrease across 3 years of OSHA reporting.

The safest year on record was 2017, at a TCR of 0.0, while 2016 saw the highest rate, at 11.7, a spread of 11.7 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.

Summed across those 4 reporting years, JM Tungste-Met recorded 5 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.

Verify This Employer with OSHA

The 5 injuries, 2 illnesses shown on this page for JM Tungste-Met are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.

Verify on OSHA Establishment Search

Source: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331492 - Tungsten carbide powder made by metallurgical process.

DART Rate, Transparent Calculation (2019)

What is the DART rate formula?

DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.

1 DART incidents × 200,000 ÷ 135,066 hours worked = 1.48 DART

Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping

Cross-Validating Context, Establishment vs Industry vs State

Benchmark TCR Source
JM Tungste-Met (this establishment) 3.66 OSHA ITA Form 300A, 4-year avg
Nonferrous alloys (except aluminum, copper) made in integrated secondary smelting and alloying plants industry avg 3.30 BLS IIF, NAICS 331492
West Virginia state avg (all industries) 4.81 OSHA ITA, state-level rollup

Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program

Reportable Incident Timeline

Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by JM Tungste-Met to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.

Source: OSHA Inspection Information System (IMIS) - inspection case-number records

Year-by-Year Safety Data

Year TCR DART Injuries Illnesses Fatalities
2019 3.0 1.5 2 0 0
2018 0.0 0.0 0 0 0
2017 0.0 0.0 0 0 0
2016 11.7 4.7 3 2 0

What this grade means for you

Use this grade as a relative read on JM Tungste-Met's reported OSHA injury record versus its Tungsten carbide powder made by metallurgical process peers, not a verdict on whether any single site is safe today.

  • At 111% of the Tungsten carbide powder made by metallurgical process benchmark, JM Tungste-Met reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
  • Judge this record against the wider Tungsten carbide powder made by metallurgical process sector, where injury rates vary widely, before comparing it in isolation. See the industry
  • Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another

Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.

Frequently Asked Questions

What is JM Tungste-Met's safety grade?
JM Tungste-Met has a safety grade of C (Average Safety Record). This grade is based on their average Total Case Rate (TCR) of 3.7 compared to the BLS industry benchmark of 3.3 for Tungsten carbide powder made by metallurgical process.
How many injuries has JM Tungste-Met reported?
JM Tungste-Met has reported 5 total injuries and 0 fatalities across 4 years of OSHA data (2019, 2018, 2017, 2016). This data comes from mandatory OSHA Injury Tracking Application (ITA) reports.

Similar Employers

Matched by safety record across the industry, by workforce size within West Virginia, and by nearby establishments in Oak Hill - a different peer set than the category browse links below.

Similar TCR (~3.7)

Similar size (~59 workers)

Nearby in Oak Hill

Data Source: OSHA Injury Tracking Application (ITA), mandatory establishment-level injury/illness reports. Grades compare employer Total Case Rate (TCR) to BLS IIF industry benchmarks. Data covers years reported by this establishment: 2019, 2018, 2017, 2016. This is publicly available government data - not a legal determination of workplace conditions.

Read our methodology - how this data is sourced, computed, and verified.

Data sourced from official public datasets. See our methodology for details. Retrieved and formatted by PlainSafetyScore Editorial

Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.