SOUTHWEST STEEL COIL New Mexico
Open-data reference.
SANTA TERESA, NM | Cold rolling steel shapes (e.g., bar, plate, rod, sheet, strip) made from purchased steel
~53 avg employees | 2 years of OSHA data
SOUTHWEST STEEL COIL New Mexico has an average TCR of 5.0, which is 153% of the industry average (3.3) for Cold rolling steel shapes (e.g., bar, plate, rod, sheet, strip) made from purchased steel. This is worse than average.
Safety Insights for SOUTHWEST STEEL COIL New Mexico
SOUTHWEST STEEL COIL New Mexico operates an establishment with approximately 53 full-time equivalent workers in SANTA TERESA, NM, classified under the Cold rolling steel shapes (e.g., bar, plate, rod, sheet, strip) made from purchased steel industry (NAICS 331221). Across 2 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 7 recordable injuries, 0 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 5.0 injuries per 100 full-time workers per year provides the anchor metric for the D letter grade (Poor Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Cold rolling steel shapes (e.g., bar, plate, rod, sheet, strip) made from purchased steel, SOUTHWEST STEEL COIL New Mexico's workforce experiences 153% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR above the benchmark flags a higher-than-typical risk profile for jobseekers, insurers, and enforcement agencies to examine.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 2 reporting cycles points to systemic hazard exposure. Readers evaluating SOUTHWEST STEEL COIL New Mexico as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from SOUTHWEST STEEL COIL New Mexico's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 331221 — Cold rolling steel shapes (e.g., bar, plate, rod, sheet, strip) made from purchased steel.
DART Rate — Transparent Calculation (2021)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
3 DART incidents × 200,000 ÷ 143,461 hours worked = 4.18 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| SOUTHWEST STEEL COIL New Mexico (this establishment) | 5.05 | OSHA ITA Form 300A, 2-year avg |
| Powder made from purchased iron or steel industry avg | 3.30 | BLS IIF, NAICS 331221 |
| New Mexico state avg (all industries) | 16.22 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by SOUTHWEST STEEL COIL New Mexico to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2021: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2020: 4 reportable incidents · 4 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2021 | 4.2 | 4.2 | 3 | 0 | 0 |
| 2020 | 5.9 | 5.9 | 4 | 0 | 0 |
Frequently Asked Questions
What is SOUTHWEST STEEL COIL New Mexico's safety grade?
How is the safety grade calculated?
How many injuries has SOUTHWEST STEEL COIL New Mexico reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.