Stanley Black and Decker
Open-data reference.
DALLAS, TX | Tools, hand, metal blade (e.g., putty knives, scrapers, screwdrivers)
~288 avg employees | 2 years of OSHA data
Stanley Black and Decker has an average TCR of 2.0, which is 62% of the industry average (3.3) for Tools, hand, metal blade (e.g., putty knives, scrapers, screwdrivers). This is better than average.
Safety Insights for Stanley Black and Decker
Stanley Black and Decker operates an establishment with approximately 288 full-time equivalent workers in DALLAS, TX, classified under the Tools, hand, metal blade (e.g., putty knives, scrapers, screwdrivers) industry (NAICS 332216). Across 2 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 11 recordable injuries, 1 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 2.0 injuries per 100 full-time workers per year provides the anchor metric for the B letter grade (Good Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Tools, hand, metal blade (e.g., putty knives, scrapers, screwdrivers), Stanley Black and Decker's workforce experiences 62% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR below the benchmark signals that controls, training, or automation may be outperforming peers.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 2 reporting cycles points to systemic hazard exposure. Readers evaluating Stanley Black and Decker as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Stanley Black and Decker's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 332216 — Tools, hand, metal blade (e.g., putty knives, scrapers, screwdrivers).
DART Rate — Transparent Calculation (2017)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 693,774 hours worked = 0.58 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Stanley Black and Decker (this establishment) | 2.05 | OSHA ITA Form 300A, 2-year avg |
| Tools, handheld, nonpowered (except kitchen-type), manufacturing industry avg | 3.30 | BLS IIF, NAICS 332216 |
| Texas state avg (all industries) | 11.19 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Stanley Black and Decker to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2017: 6 reportable incidents · 6 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2016: 6 reportable incidents · 5 injuries, 1 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2017 | 1.7 | 0.6 | 6 | 0 | 0 |
| 2016 | 2.4 | 1.2 | 5 | 1 | 0 |
Frequently Asked Questions
What is Stanley Black and Decker's safety grade?
How is the safety grade calculated?
How many injuries has Stanley Black and Decker reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.