Terex - Newton
Open-data reference.
NEWTON, NH | Construction machinery manufacturing
~77 avg employees | 4 years of OSHA data
Terex - Newton has an average TCR of 3.1, which is 94% of the industry average (3.3) for Construction machinery manufacturing. This is better than average.
Safety Insights for Terex - Newton
Terex - Newton operates an establishment with approximately 77 full-time equivalent workers in NEWTON, NH, classified under the Construction machinery manufacturing industry (NAICS 333120). Across 4 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 10 recordable injuries, 0 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 3.1 injuries per 100 full-time workers per year provides the anchor metric for the C letter grade (Average Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Construction machinery manufacturing, Terex - Newton's workforce experiences 94% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR below the benchmark signals that controls, training, or automation may be outperforming peers.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 4 reporting cycles points to systemic hazard exposure. Readers evaluating Terex - Newton as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Terex - Newton's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 333120 — Construction machinery manufacturing.
DART Rate — Transparent Calculation (2021)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 145,954 hours worked = 2.74 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Terex - Newton (this establishment) | 3.09 | OSHA ITA Form 300A, 4-year avg |
| Construction machinery manufacturing industry avg | 3.30 | BLS IIF, NAICS 333120 |
| New Hampshire state avg (all industries) | 9.50 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Terex - Newton to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2021: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2020: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2019: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2018: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2021 | 2.7 | 2.7 | 2 | 0 | 0 |
| 2020 | 3.1 | 1.5 | 2 | 0 | 0 |
| 2019 | 3.4 | 2.3 | 3 | 0 | 0 |
| 2018 | 3.2 | 2.1 | 3 | 0 | 0 |
Frequently Asked Questions
What is Terex - Newton's safety grade?
How is the safety grade calculated?
How many injuries has Terex - Newton reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.