Electronics/Industrial Controls Distributor · Georgia
3505-ADC Main Campus
Cumming, GA · ~236 workers · 3 years of OSHA Injury Tracking Application data.
- A
- Excellent Safety Record
- 1.1
- Avg TCR
- 2.2
- Industry avg
- 0
- Fatalities
The verdict
3505-ADC Main Campus runs at 49% of its industry's injury rate - far safer than the typical Electronics/Industrial Controls Distributor workplace, earning a grade A.
- A
- Excellent Safety Record
- 1.1
- avg TCR · per 100 workers
- 2.2
- industry benchmark (BLS)
- 7
- recordable injuries tracked
Grade compares 3505-ADC Main Campus's OSHA Total Case Rate of 1.1 to the Electronics/Industrial Controls Distributor BLS benchmark of 2.2 (49% of benchmark) across 3 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
3505-ADC Main Campus's yearly Total Case Rate, against the 2.2 industry benchmark.
Where 3505-ADC Main Campus falls in its industry
1,676 Electronics/Industrial Control establishmentsSafer than 58% of graded establishments in this industry, whose median TCR is 1.4.
Narrower to Georgia alone (the establishments it most directly competes with for workers and contracts): ranked #25 safest of 56 Electronics/Industrial Control employers in Georgia.
Trend analysis for 3505-ADC Main Campus
Between 2016 and 2019, 3505-ADC Main Campus's Total Case Rate held roughly steady from 0.0 to 1.4 recordable injuries per 100 full-time workers, a 0% change across 3 years of OSHA reporting.
The safest year on record was 2016, at a TCR of 0.0, while 2018 saw the highest rate, at 1.8, a spread of 1.8 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 3 reporting years, 3505-ADC Main Campus recorded 7 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 3-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 7 injuries shown on this page for 3505-ADC Main Campus are sourced from its own 3 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 423610 - Electronics/Industrial Controls Distributor.
DART Rate, Transparent Calculation (2019)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
3 DART incidents × 200,000 ÷ 559,503 hours worked = 1.07 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| 3505-ADC Main Campus (this establishment) | 1.07 | OSHA ITA Form 300A, 3-year avg |
| Distribution equipment, electrical, merchant wholesalers industry avg | 2.20 | BLS IIF, NAICS 423610 |
| Georgia state avg (all industries) | 4.11 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by 3505-ADC Main Campus to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2019: 4 reportable incidents · 4 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2019 | 1.4 | 1.1 | 4 | 0 | 0 |
| 2018 | 1.8 | 1.8 | 3 | 0 | 0 |
| 2016 | 0.0 | 0.0 | 0 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on 3505-ADC Main Campus's reported OSHA injury record, strong versus its Electronics/Industrial Controls Distributor peers, but not a guarantee about any single site today.
- At 49% of the Electronics/Industrial Controls Distributor benchmark, 3505-ADC Main Campus reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Electronics/Industrial Controls Distributor sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is 3505-ADC Main Campus's safety grade?
How many injuries has 3505-ADC Main Campus reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Georgia, and by nearby establishments in Cumming - a different peer set than the category browse links below.
Similar TCR (~1.1)
Similar size (~236 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.