Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing · Arkansas
Daisy Manufacturing Company
Rogers, AR · ~64 workers · 2 years of OSHA Injury Tracking Application data.
- F
- Failing Safety Record
- 11.5
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Daisy Manufacturing Company runs at 348% of its industry's injury rate - far more dangerous than the typical Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing workplace, earning a grade F.
- F
- Failing Safety Record
- 11.5
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 14
- recordable injuries tracked
Grade compares Daisy Manufacturing Company's OSHA Total Case Rate of 11.5 to the Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing BLS benchmark of 3.3 (348% of benchmark) across 2 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Daisy Manufacturing Company's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Daisy Manufacturing Company falls in its industry
51 Ammunition, small arms (i.e., establishmentsSafer than 4% of graded establishments in this industry, whose median TCR is 2.5.
Narrower to Arkansas alone (the establishments it most directly competes with for workers and contracts): ranked #8 safest of 8 Ammunition, small arms (i.e., employers in Arkansas.
Trend analysis for Daisy Manufacturing Company
Between 2016 and 2017, Daisy Manufacturing Company's Total Case Rate worsened from 6.8 to 16.2 recordable injuries per 100 full-time workers, a 137% increase across 1 year of OSHA reporting.
The safest year on record was 2016, at a TCR of 6.8, while 2017 saw the highest rate, at 16.2, a spread of 9.3 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 2 reporting years, Daisy Manufacturing Company recorded 14 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 2-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 14 injuries shown on this page for Daisy Manufacturing Company are sourced from its own 2 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 332992 - Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing.
DART Rate, Transparent Calculation (2017)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
7 DART incidents × 200,000 ÷ 123,573 hours worked = 11.33 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Daisy Manufacturing Company (this establishment) | 11.50 | OSHA ITA Form 300A, 2-year avg |
| Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing industry avg | 3.30 | BLS IIF, NAICS 332992 |
| Arkansas state avg (all industries) | 3.83 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Daisy Manufacturing Company to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2017: 10 reportable incidents · 10 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 4 reportable incidents · 4 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2017 | 16.2 | 11.3 | 10 | 0 | 0 |
| 2016 | 6.8 | 6.8 | 4 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Daisy Manufacturing Company's reported OSHA injury record versus its Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing peers, not a verdict on whether any single site is safe today.
- At 348% of the Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing benchmark, Daisy Manufacturing Company reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Ammunition, small arms (i.e., 30 mm. or less, 1.18 inch or less), manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Daisy Manufacturing Company's safety grade?
How many injuries has Daisy Manufacturing Company reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Arkansas, and by nearby establishments in Rogers - a different peer set than the category browse links below.
Similar TCR (~11.5)
Similar size (~64 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.