Fluorocarbon fibers and filaments manufacturing · Georgia
FiberVisions Products
ATHENS, GA · ~83 workers · 4 years of OSHA Injury Tracking Application data.
- A
- Excellent Safety Record
- 1.6
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
FiberVisions Products runs at 48% of its industry's injury rate - far safer than the typical Fluorocarbon fibers and filaments manufacturing workplace, earning a grade A.
- A
- Excellent Safety Record
- 1.6
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 6
- recordable injuries tracked
Grade compares FiberVisions Products's OSHA Total Case Rate to the BLS industry benchmark across 4 years of Form 300A filings (2016–2024).
Injury rate over time
FiberVisions Products's yearly Total Case Rate, against the 3.3 industry benchmark.
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 325220.
Where FiberVisions Products falls in its industry
70 Fluorocarbon fibers and filame establishmentsSafer than 57% of graded establishments in this industry, whose median TCR is 1.9.
FiberVisions Products has an average TCR of 1.6, which is 48% of the industry average (3.3) for Fluorocarbon fibers and filaments manufacturing. This is significantly better than average.
Safety Insights for FiberVisions Products
FiberVisions Products operates an establishment with approximately 83 full-time equivalent workers in ATHENS, GA, classified under the Fluorocarbon fibers and filaments manufacturing industry (NAICS 325220). Across 4 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 6 recordable injuries, 0 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 1.6 injuries per 100 full-time workers per year provides the anchor metric for the A letter grade (Excellent Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.3 for Fluorocarbon fibers and filaments manufacturing, FiberVisions Products's workforce experiences 48% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked, a 200,000-hour exposure base equals roughly 100 full-time workers, so establishments with very different headcounts can be compared directly. A TCR below the benchmark signals that controls, training, or automation may be outperforming peers.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 4 reporting cycles points to systemic hazard exposure. Readers evaluating FiberVisions Products as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries, there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from FiberVisions Products's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 325220 - Fluorocarbon fibers and filaments manufacturing.
DART Rate, Transparent Calculation (2021)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 185,011 hours worked = 2.16 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| FiberVisions Products (this establishment) | 1.60 | OSHA ITA Form 300A, 4-year avg |
| Cellulosic fibers and filaments manufacturing industry avg | 3.30 | BLS IIF, NAICS 325220 |
| Georgia state avg (all industries) | 4.11 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by FiberVisions Products to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2021: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2020: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2019: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2021 | 2.2 | 2.2 | 2 | 0 | 0 |
| 2020 | 2.2 | 1.1 | 2 | 0 | 0 |
| 2019 | 0.0 | 0.0 | 0 | 0 | 0 |
| 2018 | 2.1 | 0.0 | 2 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on FiberVisions Products's reported OSHA injury record, strong versus its Fluorocarbon fibers and filaments manufacturing peers, but not a guarantee about any single site today.
- At 48% of the Fluorocarbon fibers and filaments manufacturing benchmark, FiberVisions Products reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Fluorocarbon fibers and filaments manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is FiberVisions Products's safety grade?
How is the safety grade calculated?
How many injuries has FiberVisions Products reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology - how this data is sourced, computed, and verified.