Axle bearings, automotive, truck, and bus, manufacturing · Indiana
NTK Precision Axle Corp. Anderson
Anderson, IN · ~91 workers · 2 years of OSHA Injury Tracking Application data.
- B
- Good Safety Record
- 2.7
- Avg TCR
- 5.4
- Industry avg
- 0
- Fatalities
The verdict
NTK Precision Axle Corp. Anderson runs at 50% of its industry's injury rate - safer than the typical Axle bearings, automotive, truck, and bus, manufacturing workplace, earning a grade B.
- B
- Good Safety Record
- 2.7
- avg TCR · per 100 workers
- 5.4
- industry benchmark (BLS)
- 6
- recordable injuries tracked
Grade compares NTK Precision Axle Corp. Anderson's OSHA Total Case Rate of 2.7 to the Axle bearings, automotive, truck, and bus, manufacturing BLS benchmark of 5.4 (50% of benchmark) across 2 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
NTK Precision Axle Corp. Anderson's yearly Total Case Rate, against the 5.4 industry benchmark.
Where NTK Precision Axle Corp. Anderson falls in its industry
339 Axle bearings, automotive, tru establishmentsSafer than 48% of graded establishments in this industry, whose median TCR is 2.6.
Narrower to Indiana alone (the establishments it most directly competes with for workers and contracts): ranked #20 safest of 43 Axle bearings, automotive, tru employers in Indiana.
Trend analysis for NTK Precision Axle Corp. Anderson
Between 2018 and 2019, NTK Precision Axle Corp. Anderson's Total Case Rate worsened from 1.3 to 4.1 recordable injuries per 100 full-time workers, a 216% increase across 1 year of OSHA reporting.
The safest year on record was 2018, at a TCR of 1.3, while 2019 saw the highest rate, at 4.1, a spread of 2.8 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 2 reporting years, NTK Precision Axle Corp. Anderson recorded 6 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 2-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 6 injuries shown on this page for NTK Precision Axle Corp. Anderson are sourced from its own 2 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 336350 - Axle bearings, automotive, truck, and bus, manufacturing.
DART Rate, Transparent Calculation (2019)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 243,597 hours worked = 1.64 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| NTK Precision Axle Corp. Anderson (this establishment) | 2.71 | OSHA ITA Form 300A, 2-year avg |
| Transmissions and parts, automotive, truck, and bus, manufacturing industry avg | 5.40 | BLS IIF, NAICS 336350 |
| Indiana state avg (all industries) | 4.53 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by NTK Precision Axle Corp. Anderson to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2019: 5 reportable incidents · 5 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2019 | 4.1 | 1.6 | 5 | 0 | 0 |
| 2018 | 1.3 | 1.3 | 1 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on NTK Precision Axle Corp. Anderson's reported OSHA injury record, strong versus its Axle bearings, automotive, truck, and bus, manufacturing peers, but not a guarantee about any single site today.
- At 50% of the Axle bearings, automotive, truck, and bus, manufacturing benchmark, NTK Precision Axle Corp. Anderson reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Axle bearings, automotive, truck, and bus, manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is NTK Precision Axle Corp. Anderson's safety grade?
How many injuries has NTK Precision Axle Corp. Anderson reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Indiana, and by nearby establishments in Anderson - a different peer set than the category browse links below.
Similar TCR (~2.7)
Similar size (~91 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.