Animal feed mills (except dog and cat) manufacturing · Wisconsin
Owen Feed Mill
CHIPPEWA FALLS, WI · ~37 workers · 2 years of OSHA Injury Tracking Application data.
- C
- Average Safety Record
- 4.0
- Avg TCR
- 3.9
- Industry avg
- 0
- Fatalities
The verdict
Owen Feed Mill runs at 102% of its industry's injury rate — about level with the typical Animal feed mills (except dog and cat) manufacturing workplace — earning a grade C.
- C
- Average Safety Record
- 4.0
- avg TCR · per 100 workers
- 3.9
- industry benchmark (BLS)
- 3
- recordable injuries tracked
Grade compares Owen Feed Mill's OSHA Total Case Rate to the BLS industry benchmark across 2 years of Form 300A filings (2016–2024).
Injury rate over time
Owen Feed Mill's yearly Total Case Rate, against the 3.9 industry benchmark.
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 311119.
Owen Feed Mill has an average TCR of 4.0, which is 102% of the industry average (3.9) for Animal feed mills (except dog and cat) manufacturing. This is worse than average.
Safety Insights for Owen Feed Mill
Owen Feed Mill operates an establishment with approximately 37 full-time equivalent workers in CHIPPEWA FALLS, WI, classified under the Animal feed mills (except dog and cat) manufacturing industry (NAICS 311119). Across 2 years of mandatory OSHA Injury Tracking Application (ITA) reporting, this employer has accumulated 3 recordable injuries, 0 occupational illnesses, and 0 workplace fatalities. The average Total Case Rate (TCR) of 4.0 injuries per 100 full-time workers per year provides the anchor metric for the C letter grade (Average Safety Record).
Benchmarked against the Bureau of Labor Statistics industry average of 3.9 for Animal feed mills (except dog and cat) manufacturing, Owen Feed Mill's workforce experiences 102% of the typical injury burden. This ratio matters because TCR already normalizes for hours worked — a 200,000-hour exposure base equals roughly 100 full-time workers — so establishments with very different headcounts can be compared directly. A TCR above the benchmark flags a higher-than-typical risk profile for jobseekers, insurers, and enforcement agencies to examine.
Multi-year trend analysis is the single most reliable signal here: a one-year spike could reflect a single severe event, whereas sustained elevation across 2 reporting cycles points to systemic hazard exposure. Readers evaluating Owen Feed Mill as an employer, contractor, investment, or regulatory target should examine the yearly DART rate (days away, restricted, or transferred), the fatality count of 0, and any year-over-year deterioration shown in the table below. All figures come directly from employer-submitted OSHA Form 300A summaries — there is no modeling, estimation, or third-party adjustment layered on top of the government data.
Verify This Employer with OSHA
All injury, illness, and fatality figures on this page are sourced from Owen Feed Mill's own mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source — name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor — OSHA Establishment-Specific Injury and Illness Data. NAICS 311119 — Animal feed mills (except dog and cat) manufacturing.
DART Rate — Transparent Calculation (2023)
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
3 DART incidents × 200,000 ÷ 75,476 hours worked = 7.95 DART
Methodology: 29 CFR 1904 — OSHA Form 300A recordkeeping
Cross-Validating Context — Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Owen Feed Mill (this establishment) | 3.98 | OSHA ITA Form 300A, 2-year avg |
| Grain Mill Animal Feed industry avg | 3.90 | BLS IIF, NAICS 311119 |
| Wisconsin state avg (all industries) | 4.92 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics — Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Owen Feed Mill to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2023: 3 reportable incidents · 3 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
- 2022: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities — OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) — inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2023 | 8.0 | 8.0 | 3 | 0 | 0 |
| 2022 | 0.0 | 0.0 | 0 | 0 | 0 |
Frequently Asked Questions
What is Owen Feed Mill's safety grade?
How is the safety grade calculated?
How many injuries has Owen Feed Mill reported?
Where does PlainSafetyScore get its data?
Explore More Safety Data
Read our methodology — how this data is sourced, computed, and verified.