Injection molding machinery for plastics manufacturing · Connecticut
Southwest Mold, Inc dba Seitz
Torrington, CT · ~137 workers · 4 years of OSHA Injury Tracking Application data.
- D
- Poor Safety Record
- 4.2
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Southwest Mold, Inc dba Seitz runs at 128% of its industry's injury rate - more dangerous than the typical Injection molding machinery for plastics manufacturing workplace, earning a grade D.
- D
- Poor Safety Record
- 4.2
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 15
- recordable injuries tracked
Grade compares Southwest Mold, Inc dba Seitz's OSHA Total Case Rate of 4.2 to the Injection molding machinery for plastics manufacturing BLS benchmark of 3.3 (128% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Southwest Mold, Inc dba Seitz's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Southwest Mold, Inc dba Seitz falls in its industry
499 Injection molding machinery fo establishmentsSafer than 29% of graded establishments in this industry, whose median TCR is 2.7.
Narrower to Connecticut alone (the establishments it most directly competes with for workers and contracts): ranked #7 safest of 9 Injection molding machinery fo employers in Connecticut.
Trend analysis for Southwest Mold, Inc dba Seitz
Between 2021 and 2024, Southwest Mold, Inc dba Seitz's Total Case Rate held roughly steady from 0.0 to 6.7 recordable injuries per 100 full-time workers, a 0% change across 3 years of OSHA reporting.
The safest year on record was 2021, at a TCR of 0.0, while 2022 saw the highest rate, at 7.9, a spread of 7.9 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, Southwest Mold, Inc dba Seitz recorded 15 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 15 injuries shown on this page for Southwest Mold, Inc dba Seitz are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 333249 - Injection molding machinery for plastics manufacturing.
DART Rate, Transparent Calculation (2024)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
5 DART incidents × 200,000 ÷ 208,601 hours worked = 4.79 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Southwest Mold, Inc dba Seitz (this establishment) | 4.23 | OSHA ITA Form 300A, 4-year avg |
| Chemical processing machinery and equipment manufacturing industry avg | 3.30 | BLS IIF, NAICS 333249 |
| Connecticut state avg (all industries) | 6.15 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Southwest Mold, Inc dba Seitz to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 7 reportable incidents · 7 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2023: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2022: 6 reportable incidents · 6 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2021: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 6.7 | 4.8 | 7 | 0 | 0 |
| 2023 | 2.3 | 2.3 | 2 | 0 | 0 |
| 2022 | 7.9 | 7.9 | 6 | 0 | 0 |
| 2021 | 0.0 | 0.0 | 0 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Southwest Mold, Inc dba Seitz's reported OSHA injury record versus its Injection molding machinery for plastics manufacturing peers, not a verdict on whether any single site is safe today.
- At 128% of the Injection molding machinery for plastics manufacturing benchmark, Southwest Mold, Inc dba Seitz reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Injection molding machinery for plastics manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Southwest Mold, Inc dba Seitz's safety grade?
How many injuries has Southwest Mold, Inc dba Seitz reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Connecticut, and by nearby establishments in Torrington - a different peer set than the category browse links below.
Similar TCR (~4.2)
Similar size (~137 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.