Shelving (except wire) manufacturing · Colorado

Teilhaber Manufacturing Corporation

Broomfield, CO · ~27 workers · 3 years of OSHA Injury Tracking Application data.

F
Failing Safety Record
12.6
Avg TCR
3.3
Industry avg
0
Fatalities

The verdict

Teilhaber Manufacturing Corporation runs at 383% of its industry's injury rate - far more dangerous than the typical Shelving (except wire) manufacturing workplace, earning a grade F.

F
Failing Safety Record
12.6
avg TCR · per 100 workers
3.3
industry benchmark (BLS)
10
recordable injuries tracked

Grade compares Teilhaber Manufacturing Corporation's OSHA Total Case Rate of 12.6 to the Shelving (except wire) manufacturing BLS benchmark of 3.3 (383% of benchmark) across 3 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.

Injury rate over time

Teilhaber Manufacturing Corporation's yearly Total Case Rate, against the 3.3 industry benchmark.

05101520 201720182019 17.83.3 Industry benchmarkTeilhaber Manufacturing Corporation TCR
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 337215.

Where Teilhaber Manufacturing Corporation falls in its industry

242 Shelving (except wire) manufac establishments

Safer than 4% of graded establishments in this industry, whose median TCR is 4.8.

More dangerous than peersSafer than peers

Trend analysis for Teilhaber Manufacturing Corporation

Between 2017 and 2019, Teilhaber Manufacturing Corporation's Total Case Rate worsened from 3.7 to 17.8 recordable injuries per 100 full-time workers, a 385% increase across 2 years of OSHA reporting.

The safest year on record was 2017, at a TCR of 3.7, while 2019 saw the highest rate, at 17.8, a spread of 14.1 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.

Summed across those 3 reporting years, Teilhaber Manufacturing Corporation recorded 10 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 3-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.

Verify This Employer with OSHA

The 10 injuries shown on this page for Teilhaber Manufacturing Corporation are sourced from its own 3 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.

Verify on OSHA Establishment Search

Source: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 337215 - Shelving (except wire) manufacturing.

DART Rate, Transparent Calculation (2019)

What is the DART rate formula?

DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.

1 DART incidents × 200,000 ÷ 56,086 hours worked = 3.57 DART

Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping

Cross-Validating Context, Establishment vs Industry vs State

Benchmark TCR Source
Teilhaber Manufacturing Corporation (this establishment) 12.64 OSHA ITA Form 300A, 3-year avg
Fixtures, store display, manufacturing industry avg 3.30 BLS IIF, NAICS 337215
Colorado state avg (all industries) 5.41 OSHA ITA, state-level rollup

Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program

Reportable Incident Timeline

Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Teilhaber Manufacturing Corporation to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.

Source: OSHA Inspection Information System (IMIS) - inspection case-number records

Year-by-Year Safety Data

Year TCR DART Injuries Illnesses Fatalities
2019 17.8 3.6 5 0 0
2018 16.4 16.4 4 0 0
2017 3.7 3.7 1 0 0

What this grade means for you

Use this grade as a relative read on Teilhaber Manufacturing Corporation's reported OSHA injury record versus its Shelving (except wire) manufacturing peers, not a verdict on whether any single site is safe today.

  • At 383% of the Shelving (except wire) manufacturing benchmark, Teilhaber Manufacturing Corporation reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
  • Judge this record against the wider Shelving (except wire) manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
  • Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another

Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.

Frequently Asked Questions

What is Teilhaber Manufacturing Corporation's safety grade?
Teilhaber Manufacturing Corporation has a safety grade of F (Failing Safety Record). This grade is based on their average Total Case Rate (TCR) of 12.6 compared to the BLS industry benchmark of 3.3 for Shelving (except wire) manufacturing.
How many injuries has Teilhaber Manufacturing Corporation reported?
Teilhaber Manufacturing Corporation has reported 10 total injuries and 0 fatalities across 3 years of OSHA data (2019, 2018, 2017). This data comes from mandatory OSHA Injury Tracking Application (ITA) reports.

Similar Employers

Matched by safety record across the industry, by workforce size within Colorado, and by nearby establishments in Broomfield - a different peer set than the category browse links below.

Similar TCR (~12.6)

Similar size (~27 workers)

Nearby in Broomfield

Data Source: OSHA Injury Tracking Application (ITA), mandatory establishment-level injury/illness reports. Grades compare employer Total Case Rate (TCR) to BLS IIF industry benchmarks. Data covers years reported by this establishment: 2019, 2018, 2017. This is publicly available government data - not a legal determination of workplace conditions.

Read our methodology - how this data is sourced, computed, and verified.

Data sourced from official public datasets. See our methodology for details. Retrieved and formatted by PlainSafetyScore Editorial

Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.