Armored military vehicles (except tanks) and parts manufacturing · Michigan

AM General Technology and Engineering Center

Auburn Hills, MI · ~176 workers · 4 years of OSHA Injury Tracking Application data.

A
Excellent Safety Record
0.1
Avg TCR
3.3
Industry avg
0
Fatalities

The verdict

AM General Technology and Engineering Center runs at 4% of its industry's injury rate - far safer than the typical Armored military vehicles (except tanks) and parts manufacturing workplace, earning a grade A.

A
Excellent Safety Record
0.1
avg TCR · per 100 workers
3.3
industry benchmark (BLS)
1
recordable injuries tracked

Grade compares AM General Technology and Engineering Center's OSHA Total Case Rate of 0.1 to the Armored military vehicles (except tanks) and parts manufacturing BLS benchmark of 3.3 (4% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.

Injury rate over time

AM General Technology and Engineering Center's yearly Total Case Rate, against the 3.3 industry benchmark.

-101234 2017201820192020 03.3 Industry benchmarkAM General Technology and Engineering Center TCR
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 336992.

Where AM General Technology and Engineering Center falls in its industry

52 Armored military vehicles (exc establishments

Safer than 90% of graded establishments in this industry, whose median TCR is 2.9.

More dangerous than peersSafer than peers

Narrower to Michigan alone (the establishments it most directly competes with for workers and contracts): ranked #2 safest of 11 Armored military vehicles (exc employers in Michigan.

Trend analysis for AM General Technology and Engineering Center

Between 2017 and 2020, AM General Technology and Engineering Center's Total Case Rate improved from 0.6 to 0.0 recordable injuries per 100 full-time workers, a 100% decrease across 3 years of OSHA reporting.

The safest year on record was 2018, at a TCR of 0.0, while 2017 saw the highest rate, at 0.6, a spread of 0.6 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.

Summed across those 4 reporting years, AM General Technology and Engineering Center recorded 1 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.

Verify This Employer with OSHA

The 1 injuries shown on this page for AM General Technology and Engineering Center are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.

Verify on OSHA Establishment Search

Source: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 336992 - Armored military vehicles (except tanks) and parts manufacturing.

DART Rate, Transparent Calculation (2020)

What is the DART rate formula?

DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.

0 DART incidents × 200,000 ÷ 336,960 hours worked = 0.00 DART

Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping

Cross-Validating Context, Establishment vs Industry vs State

Benchmark TCR Source
AM General Technology and Engineering Center (this establishment) 0.14 OSHA ITA Form 300A, 4-year avg
Armored military vehicles (except tanks) and parts manufacturing industry avg 3.30 BLS IIF, NAICS 336992
Michigan state avg (all industries) 4.73 OSHA ITA, state-level rollup

Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program

Reportable Incident Timeline

Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by AM General Technology and Engineering Center to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.

Source: OSHA Inspection Information System (IMIS) - inspection case-number records

Year-by-Year Safety Data

Year TCR DART Injuries Illnesses Fatalities
2020 0.0 0.0 0 0 0
2019 0.0 0.0 0 0 0
2018 0.0 0.0 0 0 0
2017 0.6 0.6 1 0 0

What this grade means for you

Use this grade as a relative read on AM General Technology and Engineering Center's reported OSHA injury record, strong versus its Armored military vehicles (except tanks) and parts manufacturing peers, but not a guarantee about any single site today.

  • At 4% of the Armored military vehicles (except tanks) and parts manufacturing benchmark, AM General Technology and Engineering Center reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
  • Judge this record against the wider Armored military vehicles (except tanks) and parts manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
  • Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another

Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.

Frequently Asked Questions

What is AM General Technology and Engineering Center's safety grade?
AM General Technology and Engineering Center has a safety grade of A (Excellent Safety Record). This grade is based on their average Total Case Rate (TCR) of 0.1 compared to the BLS industry benchmark of 3.3 for Armored military vehicles (except tanks) and parts manufacturing.
How many injuries has AM General Technology and Engineering Center reported?
AM General Technology and Engineering Center has reported 1 total injuries and 0 fatalities across 4 years of OSHA data (2020, 2019, 2018, 2017). This data comes from mandatory OSHA Injury Tracking Application (ITA) reports.

Similar Employers

Matched by safety record across the industry, by workforce size within Michigan, and by nearby establishments in Auburn Hills - a different peer set than the category browse links below.

Similar TCR (~0.1)

Similar size (~176 workers)

Nearby in Auburn Hills

Data Source: OSHA Injury Tracking Application (ITA), mandatory establishment-level injury/illness reports. Grades compare employer Total Case Rate (TCR) to BLS IIF industry benchmarks. Data covers years reported by this establishment: 2020, 2019, 2018, 2017. This is publicly available government data - not a legal determination of workplace conditions.

Read our methodology - how this data is sourced, computed, and verified.

Data sourced from official public datasets. See our methodology for details. Retrieved and formatted by PlainSafetyScore Editorial

Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.