Powder, nonferrous metals (except aluminum, copper), made from purchased metal · Texas
Atomized Products Group
Garland, TX · ~20 workers · 4 years of OSHA Injury Tracking Application data.
- D
- Poor Safety Record
- 5.7
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Atomized Products Group runs at 172% of its industry's injury rate - more dangerous than the typical Powder, nonferrous metals (except aluminum, copper), made from purchased metal workplace, earning a grade D.
- D
- Poor Safety Record
- 5.7
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 5
- recordable injuries tracked
Grade compares Atomized Products Group's OSHA Total Case Rate of 5.7 to the Powder, nonferrous metals (except aluminum, copper), made from purchased metal BLS benchmark of 3.3 (172% of benchmark) across 4 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Atomized Products Group's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Atomized Products Group falls in its industry
139 Powder, nonferrous metals (exc establishmentsSafer than 24% of graded establishments in this industry, whose median TCR is 3.6.
Narrower to Texas alone (the establishments it most directly competes with for workers and contracts): ranked #13 safest of 14 Powder, nonferrous metals (exc employers in Texas.
Trend analysis for Atomized Products Group
Between 2016 and 2020, Atomized Products Group's Total Case Rate held roughly steady from 0.0 to 9.4 recordable injuries per 100 full-time workers, a 0% change across 4 years of OSHA reporting.
The safest year on record was 2016, at a TCR of 0.0, while 2020 saw the highest rate, at 9.4, a spread of 9.4 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, Atomized Products Group recorded 5 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 5 injuries shown on this page for Atomized Products Group are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331492 - Powder, nonferrous metals (except aluminum, copper), made from purchased metal.
DART Rate, Transparent Calculation (2020)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 42,500 hours worked = 9.41 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Atomized Products Group (this establishment) | 5.69 | OSHA ITA Form 300A, 4-year avg |
| Nonferrous alloys (except aluminum, copper) made in integrated secondary smelting and alloying plants industry avg | 3.30 | BLS IIF, NAICS 331492 |
| Texas state avg (all industries) | 3.73 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Atomized Products Group to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2020: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2019: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2018: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 0 reportable incidents · 0 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2020 | 9.4 | 9.4 | 2 | 0 | 0 |
| 2019 | 4.4 | 4.4 | 1 | 0 | 0 |
| 2018 | 8.9 | 8.9 | 2 | 0 | 0 |
| 2016 | 0.0 | 0.0 | 0 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Atomized Products Group's reported OSHA injury record versus its Powder, nonferrous metals (except aluminum, copper), made from purchased metal peers, not a verdict on whether any single site is safe today.
- At 172% of the Powder, nonferrous metals (except aluminum, copper), made from purchased metal benchmark, Atomized Products Group reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Powder, nonferrous metals (except aluminum, copper), made from purchased metal sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Atomized Products Group's safety grade?
How many injuries has Atomized Products Group reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Texas, and by nearby establishments in Garland - a different peer set than the category browse links below.
Similar TCR (~5.7)
Similar size (~20 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.