Siding contractors · Arizona

Gen3 Az LLC

Tempe, AZ · ~111 workers · 7 years of OSHA Injury Tracking Application data.

C
Average Safety Record
2.3
Avg TCR
2.8
Industry avg
0
Fatalities

The verdict

Gen3 Az LLC runs at 83% of its industry's injury rate - about level with the typical Siding contractors workplace, earning a grade C.

C
Average Safety Record
2.3
avg TCR · per 100 workers
2.8
industry benchmark (BLS)
14
recordable injuries tracked

Grade compares Gen3 Az LLC's OSHA Total Case Rate of 2.3 to the Siding contractors BLS benchmark of 2.8 (83% of benchmark) across 7 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.

Injury rate over time

Gen3 Az LLC's yearly Total Case Rate, against the 2.8 industry benchmark.

-202468 2016201720182019202020212024 1.32.8 Industry benchmarkGen3 Az LLC TCR
Total Case Rate (recordable injuries per 100 full-time workers), OSHA ITA Form 300A. Industry benchmark: BLS IIF, NAICS 238170.

Where Gen3 Az LLC falls in its industry

160 Siding contractors establishments

Safer than 69% of graded establishments in this industry, whose median TCR is 3.7.

More dangerous than peersSafer than peers

Narrower to Arizona alone (the establishments it most directly competes with for workers and contracts): ranked #1 safest of 5 Siding contractors employers in Arizona.

Trend analysis for Gen3 Az LLC

Between 2016 and 2024, Gen3 Az LLC's Total Case Rate improved from 4.4 to 1.3 recordable injuries per 100 full-time workers, a 71% decrease across 8 years of OSHA reporting.

The safest year on record was 2017, at a TCR of 0.0, while 2021 saw the highest rate, at 6.7, a spread of 6.7 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.

Summed across those 7 reporting years, Gen3 Az LLC recorded 14 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 7-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.

Verify This Employer with OSHA

The 14 injuries shown on this page for Gen3 Az LLC are sourced from its own 7 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.

Verify on OSHA Establishment Search

Source: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 238170 - Siding contractors.

DART Rate, Transparent Calculation (2024)

What is the DART rate formula?

DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.

0 DART incidents × 200,000 ÷ 156,612 hours worked = 0.00 DART

Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping

Cross-Validating Context, Establishment vs Industry vs State

Benchmark TCR Source
Gen3 Az LLC (this establishment) 2.32 OSHA ITA Form 300A, 7-year avg
Aluminum siding installation industry avg 2.80 BLS IIF, NAICS 238170
Arizona state avg (all industries) 4.73 OSHA ITA, state-level rollup

Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program

Reportable Incident Timeline

Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Gen3 Az LLC to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.

Source: OSHA Inspection Information System (IMIS) - inspection case-number records

Year-by-Year Safety Data

Year TCR DART Injuries Illnesses Fatalities
2024 1.3 0.0 1 0 0
2021 6.7 1.1 6 0 0
2020 0.0 0.0 0 0 0
2019 3.9 1.9 4 0 0
2018 0.0 0.0 0 0 0
2017 0.0 0.0 0 0 0
2016 4.4 3.0 3 0 0

What this grade means for you

Use this grade as a relative read on Gen3 Az LLC's reported OSHA injury record, strong versus its Siding contractors peers, but not a guarantee about any single site today.

  • At 83% of the Siding contractors benchmark, Gen3 Az LLC reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
  • Judge this record against the wider Siding contractors sector, where injury rates vary widely, before comparing it in isolation. See the industry
  • Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another

Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.

Frequently Asked Questions

What is Gen3 Az LLC's safety grade?
Gen3 Az LLC has a safety grade of C (Average Safety Record). This grade is based on their average Total Case Rate (TCR) of 2.3 compared to the BLS industry benchmark of 2.8 for Siding contractors.
How many injuries has Gen3 Az LLC reported?
Gen3 Az LLC has reported 14 total injuries and 0 fatalities across 7 years of OSHA data (2024, 2021, 2020, 2019, 2018, 2017, 2016). This data comes from mandatory OSHA Injury Tracking Application (ITA) reports.

Similar Employers

Matched by safety record across the industry, by workforce size within Arizona, and by nearby establishments in Tempe - a different peer set than the category browse links below.

Similar TCR (~2.3)

Similar size (~111 workers)

Nearby in Tempe

Data Source: OSHA Injury Tracking Application (ITA), mandatory establishment-level injury/illness reports. Grades compare employer Total Case Rate (TCR) to BLS IIF industry benchmarks. Data covers years reported by this establishment: 2024, 2021, 2020, 2019, 2018, 2017, 2016. This is publicly available government data - not a legal determination of workplace conditions.

Read our methodology - how this data is sourced, computed, and verified.

Data sourced from official public datasets. See our methodology for details. Retrieved and formatted by PlainSafetyScore Editorial

Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.