Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing · California
RF&M - Santa Rosa
Santa Rosa, CA · ~20 workers · 2 years of OSHA Injury Tracking Application data.
- C
- Average Safety Record
- 3.0
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
RF&M - Santa Rosa runs at 91% of its industry's injury rate - about level with the typical Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing workplace, earning a grade C.
- C
- Average Safety Record
- 3.0
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 2
- recordable injuries tracked
Grade compares RF&M - Santa Rosa's OSHA Total Case Rate of 3.0 to the Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing BLS benchmark of 3.3 (91% of benchmark) across 2 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
RF&M - Santa Rosa's yearly Total Case Rate, against the 3.3 industry benchmark.
Where RF&M - Santa Rosa falls in its industry
200 Connectors, electronic (e.g., establishmentsSafer than 17% of graded establishments in this industry, whose median TCR is 1.3.
Narrower to California alone (the establishments it most directly competes with for workers and contracts): ranked #32 safest of 37 Connectors, electronic (e.g., employers in California.
Trend analysis for RF&M - Santa Rosa
Between 2017 and 2018, RF&M - Santa Rosa's Total Case Rate worsened from 0.5 to 5.5 recordable injuries per 100 full-time workers, a 1024% increase across 1 year of OSHA reporting.
The safest year on record was 2017, at a TCR of 0.5, while 2018 saw the highest rate, at 5.5, a spread of 5.0 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 2 reporting years, RF&M - Santa Rosa recorded 2 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 2-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 2 injuries shown on this page for RF&M - Santa Rosa are sourced from its own 2 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 334417 - Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing.
DART Rate, Transparent Calculation (2018)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 36,314 hours worked = 0.00 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| RF&M - Santa Rosa (this establishment) | 3.00 | OSHA ITA Form 300A, 2-year avg |
| Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing industry avg | 3.30 | BLS IIF, NAICS 334417 |
| California state avg (all industries) | 5.64 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by RF&M - Santa Rosa to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2018: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2017: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2018 | 5.5 | 0.0 | 1 | 0 | 0 |
| 2017 | 0.5 | 0.5 | 1 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on RF&M - Santa Rosa's reported OSHA injury record, strong versus its Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing peers, but not a guarantee about any single site today.
- At 91% of the Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing benchmark, RF&M - Santa Rosa reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Connectors, electronic (e.g., coaxial, cylindrical, printed circuit, rack and panel), manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is RF&M - Santa Rosa's safety grade?
How many injuries has RF&M - Santa Rosa reported?
Similar Employers
Matched by safety record across the industry, by workforce size within California, and by nearby establishments in Santa Rosa - a different peer set than the category browse links below.
Similar TCR (~3.0)
Similar size (~20 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.