Mesh, wire, made in wire drawing mills · Tennessee
Insteel Wire Products TNS
Gallatin, TN · ~58 workers · 5 years of OSHA Injury Tracking Application data.
- D
- Poor Safety Record
- 4.6
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Insteel Wire Products TNS runs at 139% of its industry's injury rate - more dangerous than the typical Mesh, wire, made in wire drawing mills workplace, earning a grade D.
- D
- Poor Safety Record
- 4.6
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 16
- recordable injuries tracked
Grade compares Insteel Wire Products TNS's OSHA Total Case Rate of 4.6 to the Mesh, wire, made in wire drawing mills BLS benchmark of 3.3 (139% of benchmark) across 5 years of Form 300A filings (2016–2024). <a href="/methodology">See methodology</a> for reporting-limitation caveats.
Injury rate over time
Insteel Wire Products TNS's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Insteel Wire Products TNS falls in its industry
168 Mesh, wire, made in wire drawi establishmentsSafer than 50% of graded establishments in this industry, whose median TCR is 4.6.
Narrower to Tennessee alone (the establishments it most directly competes with for workers and contracts): ranked #2 safest of 6 Mesh, wire, made in wire drawi employers in Tennessee.
Trend analysis for Insteel Wire Products TNS
Between 2016 and 2024, Insteel Wire Products TNS's Total Case Rate improved from 8.5 to 1.7 recordable injuries per 100 full-time workers, a 80% decrease across 8 years of OSHA reporting.
The safest year on record was 2023, at a TCR of 1.5, while 2016 saw the highest rate, at 8.5, a spread of 7.0 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 5 reporting years, Insteel Wire Products TNS recorded 16 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 5-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 16 injuries shown on this page for Insteel Wire Products TNS are sourced from its own 5 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331222 - Mesh, wire, made in wire drawing mills.
DART Rate, Transparent Calculation (2024)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
0 DART incidents × 200,000 ÷ 115,472 hours worked = 0.00 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Insteel Wire Products TNS (this establishment) | 4.59 | OSHA ITA Form 300A, 5-year avg |
| Drawing iron or steel wire from purchased iron or steel and fabricating wire products industry avg | 3.30 | BLS IIF, NAICS 331222 |
| Tennessee state avg (all industries) | 4.09 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Insteel Wire Products TNS to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2023: 1 reportable incidents · 1 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2022: 2 reportable incidents · 2 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2021: 5 reportable incidents · 5 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2016: 7 reportable incidents · 7 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 1.7 | 0.0 | 1 | 0 | 0 |
| 2023 | 1.5 | 0.0 | 1 | 0 | 0 |
| 2022 | 4.3 | 2.1 | 2 | 0 | 0 |
| 2021 | 7.0 | 2.8 | 5 | 0 | 0 |
| 2016 | 8.5 | 3.6 | 7 | 0 | 0 |
What this grade means for you
Use this grade as a relative read on Insteel Wire Products TNS's reported OSHA injury record versus its Mesh, wire, made in wire drawing mills peers, not a verdict on whether any single site is safe today.
- At 139% of the Mesh, wire, made in wire drawing mills benchmark, Insteel Wire Products TNS reports more injuries than typical peers, ask specifically how the employer is reducing them. Know your rights
- Judge this record against the wider Mesh, wire, made in wire drawing mills sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Insteel Wire Products TNS's safety grade?
How many injuries has Insteel Wire Products TNS reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Tennessee, and by nearby establishments in Gallatin - a different peer set than the category browse links below.
Similar TCR (~4.6)
Similar size (~58 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.