Cast iron pipe and pipe fittings manufacturing · Alabama
Tyler Union Anniston
Anniston, AL · ~420 workers · 4 years of OSHA Injury Tracking Application data.
- A
- Excellent Safety Record
- 1.4
- Avg TCR
- 3.3
- Industry avg
- 0
- Fatalities
The verdict
Tyler Union Anniston runs at 41% of its industry's injury rate - far safer than the typical Cast iron pipe and pipe fittings manufacturing workplace, earning a grade A.
- A
- Excellent Safety Record
- 1.4
- avg TCR · per 100 workers
- 3.3
- industry benchmark (BLS)
- 25
- recordable injuries tracked
Grade compares Tyler Union Anniston's OSHA Total Case Rate of 1.4 to the Cast iron pipe and pipe fittings manufacturing BLS benchmark of 3.3 (41% of benchmark) across 4 years of Form 300A filings (2016–2024). This reflects reported recordable injuries, not an independent safety inspection -- underreporting is a known limitation of employer self-recordkeeping.
Injury rate over time
Tyler Union Anniston's yearly Total Case Rate, against the 3.3 industry benchmark.
Where Tyler Union Anniston falls in its industry
281 Cast iron pipe and pipe fittin establishmentsSafer than 96% of graded establishments in this industry, whose median TCR is 7.2.
Narrower to Alabama alone (the establishments it most directly competes with for workers and contracts): ranked #1 safest of 18 Cast iron pipe and pipe fittin employers in Alabama.
Trend analysis for Tyler Union Anniston
Between 2021 and 2024, Tyler Union Anniston's Total Case Rate worsened from 0.6 to 1.1 recordable injuries per 100 full-time workers, a 74% increase across 3 years of OSHA reporting.
The safest year on record was 2021, at a TCR of 0.6, while 2022 saw the highest rate, at 2.3, a spread of 1.7 points between the best and worst reporting years. That's a wide swing relative to the establishment's overall rate, worth checking the year-by-year table below for whether a single severe year is driving the average, rather than a sustained trend.
Summed across those 4 reporting years, Tyler Union Anniston recorded 25 total injuries and illnesses, with no fatalities reported in any of those years. Readers comparing establishments should weigh the 4-year trend above alongside establishment size, since a larger workforce naturally accumulates more raw incidents even at a lower per-100-worker rate.
Verify This Employer with OSHA
The 25 injuries, 1 illnesses shown on this page for Tyler Union Anniston are sourced from its own 4 years of mandatory OSHA Form 300A summaries. Cross-check the underlying establishment record directly against the federal source, name, NAICS classification, recordable case totals, and inspection history are all searchable on OSHA's Establishment-Specific Injury and Illness Data system.
Verify on OSHA Establishment SearchSource: U.S. Department of Labor, OSHA Establishment-Specific Injury and Illness Data. NAICS 331511 - Cast iron pipe and pipe fittings manufacturing.
DART Rate, Transparent Calculation (2024)
What is the DART rate formula?
DART (Days Away, Restricted, or Transferred) is computed by OSHA as incidents × 200,000 ÷ hours worked. The 200,000-hour denominator equals roughly 100 full-time workers, which lets establishments of very different sizes be compared directly.
2 DART incidents × 200,000 ÷ 923,556 hours worked = 0.43 DART
Methodology: 29 CFR 1904, OSHA Form 300A recordkeeping
Cross-Validating Context, Establishment vs Industry vs State
| Benchmark | TCR | Source |
|---|---|---|
| Tyler Union Anniston (this establishment) | 1.35 | OSHA ITA Form 300A, 4-year avg |
| Gray iron foundries industry avg | 3.30 | BLS IIF, NAICS 331511 |
| Alabama state avg (all industries) | 4.09 | OSHA ITA, state-level rollup |
Industry benchmarks: Bureau of Labor Statistics, Injuries, Illnesses, and Fatalities (IIF) program
Reportable Incident Timeline
Year-by-year reportable incidents (recordable injuries + illnesses + fatalities) submitted by Tyler Union Anniston to OSHA's Injury Tracking Application. Each row anchors to OSHA's inspection records search where you can pull the underlying inspection case numbers and citations for that establishment-year.
- 2024: 5 reportable incidents · 5 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2023: 6 reportable incidents · 6 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2022: 12 reportable incidents · 12 injuries, 0 illnesses, 0 fatalities - OSHA inspection records (case numbers)
- 2021: 3 reportable incidents · 2 injuries, 1 illnesses, 0 fatalities - OSHA inspection records (case numbers)
Source: OSHA Inspection Information System (IMIS) - inspection case-number records
Year-by-Year Safety Data
| Year | TCR | DART | Injuries | Illnesses | Fatalities |
|---|---|---|---|---|---|
| 2024 | 1.1 | 0.4 | 5 | 0 | 0 |
| 2023 | 1.4 | 0.5 | 6 | 0 | 0 |
| 2022 | 2.3 | 1.6 | 12 | 0 | 0 |
| 2021 | 0.6 | 0.4 | 2 | 1 | 0 |
What this grade means for you
Use this grade as a relative read on Tyler Union Anniston's reported OSHA injury record, strong versus its Cast iron pipe and pipe fittings manufacturing peers, but not a guarantee about any single site today.
- At 41% of the Cast iron pipe and pipe fittings manufacturing benchmark, Tyler Union Anniston reports fewer injuries than typical peers, still worth asking how safety is managed day to day. Know your rights
- Judge this record against the wider Cast iron pipe and pipe fittings manufacturing sector, where injury rates vary widely, before comparing it in isolation. See the industry
- Grades reflect 2016–2024 filings; check the latest establishment record straight from OSHA, or look up a different employer. Look up another
Safety grades reflect employers' self-reported OSHA Form 300A filings from 2016 to 2024 and can lag current conditions. A grade is not a guarantee that any specific workplace is safe or unsafe today. See our methodology and disclaimer.
Frequently Asked Questions
What is Tyler Union Anniston's safety grade?
How many injuries has Tyler Union Anniston reported?
Similar Employers
Matched by safety record across the industry, by workforce size within Alabama, and by nearby establishments in Anniston - a different peer set than the category browse links below.
Similar TCR (~1.4)
Similar size (~420 workers)
Read our methodology - how this data is sourced, computed, and verified.
Every figure and grade on PlainSafetyScore is computed directly from OSHA's published Injury Tracking Application data and BLS industry benchmarks, no number is typed in by an editor. See our editorial standards & corrections policy, the methodology behind these safety grades, or report a data error. Data current as of 2016-2024 OSHA ITA release.